How do you really feel in regards to A Step-by-Step Guide to Installing a Bathtub?
Setting up a tub isn't specifically rocket science, but it does need strong plumbing, woodworking, and often, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately challenging job. If the old bathtub is conveniently accessible, the project can move immediately; if you have to open a wall surface to get rid of the old bathtub and position the brand-new bath tub, the job is much harder. In either case, the job is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old tub and set in the new one. Make sure you have qualified yourself for the job and are comfortable attempting it. Rather than hiring a specialist to take control of a halfway-completed job, it is better to think about employing one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This short article will certainly aid you mount a brand-new bath tub in your shower room if you have actually already purchased a new tub and do not require to transform the plan of your previous water system pipes.
Your tools and product list must make up the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you should do is separate the water system. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The process of removing the existing faucets can be fairly troublesome due to the limited accessibility that is typically the case.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth all set for the staying water that will originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this procedure. Once the faucets have been eliminated, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the tap as well as the other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will need lowering couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in place between the faucet and the sink. Safeguard the tap in place with the supplier given backnut. As soon as the faucet is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap connectors. The former kind should be connected to the faucet finishes first, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been attached.
Installing the Tub
Making use of the two wood boards under its feet, place the tub in the called for position. The wood boards are helpful in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 small points.
The next goal is to ensure that the bath tub is leveled all round. This can be achieved by checking the spirit level and also adjusting the feet on the tub up until the level reads level.
To set up faucets, fit the bottom of the outermost versatile tap adapter to the suitable supply pipe by making a compression join; after that do the same for the other faucet.
Activate the supply of water as well as examine all joints as well as brand-new pipework for leaks and also tighten them if needed. Fill up the bathtub and additionally check the overflow outlet and also the regular outlet for leaks.
Finally, fix the bathroom paneling as explained in the producer's instruction manual. Tiling as well as securing around the bathtub needs to wait up until the bath tub has actually been utilized at the very least when as this will certainly settle it into its final placement.
Planning for the Setup
To start with, the supporting structure provided with the bathroom ought to be fitted (if required) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is essential to make certain that if the tap features a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps system to avoid strain on the tub.
Fit the versatile tap adapters to the bottom of both faucets using 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you utilize every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to currently be ready to be suited its last setting.
Tiling Around the Tub
In the location where the bathroom fulfills the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the installation can move enough to break a rigid seal, triggering the water to penetrate the wall in between the bath as well as the tiling, causing difficulties with dampness and also feasible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and fittings. They are marketed in tubes and cartridges, as well as are capable of sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of drenched paper or soft rope. Keep in mind to always fill up the tub with water before sealing, to permit the motion experienced when the bathtub remains in usage. The sealant can fracture fairly early if you do not take into consideration this motion before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally conveniently available on the marketplace. It is suggested to fit the ceramic tiles utilizing water-resistant or waterproof glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our topic about How to Install a Bathtub Yourself. Thanks so much for taking the time to read through our content. Enjoyed our content? Please share it. Help others find it. I appreciate reading our article about Installing A Bathtub.
More Details